SENCS1D Current Sensor Evaluation Boards

SENCS1D Current Sensor Evaluation Boards

SENCS1D Current Sensor Evaluation Boards

Features

  • Evaluation boards available separately or as a set
  • Nine different application uses cases are available
  • SENCS1Dx IC comes with each evaluation board
  • Evaluation PCBs are 50mm X 25mm
  • Power Module is included in kit

Current sensor Evaluation Boards (modules) allow a rapid test of SENIS novel integrated current sensor SENCS1Dx in various application configurations. With Evaluation Boards AC and DC currents can be measured in the range of 0.1 -100 A and bandwidth DC to 1MHz. Evaluation Boards can also be used for the detection of current spikes that occur in short time intervals, down to a few us. An Evaluation Board consist of a printed circuit board (PCB) with current carrying tracks and a 9V battery, which supplies the current sensor with a regulated 5V voltage.
EVBCS1Dx-BASIC Evaluation Board EVBCS1Dx-BASIC Evaluation Board
EVBCS1Dx-BASIC Evaluation Board
This Evaluation Board is suitable for sensing of the current in pcb traces directly located under the sensor IC for the mid-range current. The electric current is limited by the trace width of 2mm and its copper thickness (35um). PCB 1 TOTAL $120.00
EVBCS1Dx-BUS_BAR Evaluation Board EVBCS1Dx-BUS_BAR Evaluation Board
EVBCS1Dx-BUS_BAR Evaluation Board
This Evaluation Board is suitable sensing current in bus bars and flat conductors. The sensitivity depends on the width and the thickness of the conductor. Increasing the width and thickness decreases the sensitivity. PCB 1 TOTAL $120.00
EVBCS1Dx-CLAMP_ON Evaluation Board EVBCS1Dx-CLAMP_ON Evaluation Board
EVBCS1Dx-CLAMP_ON Evaluation Board
This Evaluation Board is suitable for sensing currents in the wires (conductors). The sensitivity is dependent on the diameter of the wire and the thickness of the insulation. Any wire size can be used in this application. PCB 1 TOTAL $120.00
EVBCS1Dx-COIL Evaluation Board EVBCS1Dx-COIL Evaluation Board
EVBCS1Dx-COIL Evaluation Board
This Evaluation Board is suitable for low currents (10 mA to 1A rms) and high voltage applications. Sensitivity depends on the number of turns of the wire in the coil (approx. 30mV/amp turn). PCB 1 TOTAL $120.00
EVBCS1Dx-DUAL_SENSOR Evaluation Board EVBCS1Dx-DUAL_SENSOR Evaluation Board
EVBCS1Dx-DUAL_SENSOR Evaluation Board
This Evaluation Board is suitable for sensing of the low currents on PCB’s. The board contains a sensor on the top and another one, on the other side of board. The common mode magnetic fields are canceled out with this sensor configuration. PCB 1 TOTAL $120.00
EVBCS1Dx-KIT Evaluation Kit EVBCS1Dx-KIT Evaluation Kit
EVBCS1Dx-KIT Evaluation Kit
This Evaluation Kit includes all the individual use case application modules including a SENCS1Dx Current Sensor IC for each PCB. Kit 1 TOTAL $1,000.00
EVBCS1Dx-MULTI_TURN Evaluation Board EVBCS1Dx-MULTI_TURN Evaluation Board
EVBCS1Dx-MULTI_TURN Evaluation Board
A coil composed of the current track on the PCB, with 5 loops generates the magnetic field proportional to the measured current. PCB 1 TOTAL $120.00
EVBCS1Dx-POWER Module EVBCS1Dx-POWER Module
EVBCS1Dx-POWER Module
This Evaluation Board is a power module. PCB 1 TOTAL $120.00
EVBCS1Dx-SINGLE_WIRE_LOOP Evaluation Board EVBCS1Dx-SINGLE_WIRE_LOOP Evaluation Board
EVBCS1Dx-SINGLE_WIRE_LOOP Evaluation Board
This Evaluation Board is suitable for sensing of current in the PBC traces, located directly under the sensor IC for the mid-range current. PCB 1 TOTAL $120.00
EVCBS1Dx-FERRITE Evaluation Board EVCBS1Dx-FERRITE Evaluation Board
EVCBS1Dx-FERRITE Evaluation Board
This Evaluation Board is suitable for sensing of the high current trough a conductor. The board contains the SENCS1Dx sensor in the air gap of the ferrite core that concentrates the magnetic field generated around the conductor in the air gap. PCB 1 TOTAL $120.00